Hi,

My bike was suppose to be a project which turned bad for financial reasons and so I'm selling the whole BUELL XB9SX stripped down. It's a 2005 plate Buell with 14K miles.

PM me with the part you are after and how much you are willing to pay and I will respond with a photo and other details. Everything available from working stator, frame, swing arm to piston flywheel, pistons, cases, headers, gears, cams, wheels (loads of thread on) etc etc.

Everything is in a great shape I will push for you to inspect the part before buying and if you live far, then 100% money return if you're not happy/sth's wrong!

I will update posts when sth is sold rather than list everything separately so if it's not posted, assume it's available.

I have also a brand new, unopened cometic full rebuild gasket set - I will sell it for 100 quid.
Also a new, unopened battery for a buell, 30 quid.

If you make bigger purchases I will throw in Formula + tranny oil and Amsoil engine oil for freeeeee


(starter motor is gone, oil lines are gone, indicators are gone, front exhaust bracket with strap is gone, rear pulley guards are gone)

frame is on ebay at the moment:

http://www.ebay.co.uk/itm/130618321130? ... 500wt_1287

some examples:

http://www.buellxb.com/buell_images/115 ... 0331_L.jpg
http://www.buellxb.com/buell_images/115 ... 0618_L.jpg
http://www.buellxb.com/buell_images/115 ... 0830_L.jpg
http://www.buellxb.com/buell_images/115 ... 0407_L.jpg
http://www.buellxb.com/buell_images/115 ... 0513_L.jpg

Let me know

Front light with bracket and front fairing sold.

some more photos:

This is tail riser kit, a lambda sensor and a brand new oil pressure gauge.
http://www.buellxb.com/buell_images/115 ... 0750_L.jpg


Sprockets (stator sprocket with all magnets perfectly in line and not peeling off like they sometimes like to do on buells)
http://www.buellxb.com/buell_images/115 ... 0708_L.jpg

A bueatiful carbon fibre airbox cover imported from the us:
http://www.buellxb.com/buell_images/115 ... 0541_L.jpg

Air intake painted with high quality engine paint (up to 540C) and cured. Comes with all relevant screws, connections and calibrated.
http://www.buellxb.com/buell_images/115 ... 3225_L.jpg

How much for the whole bike? Would be nice to finish your project...

_________________
08 Specialized Langster

Hi,

I've sold too many parts now to sell the whole bike. The project was a nice idea but once I realised how much all the little bearings, seals and screws and bits and pieces will add to the initial cost I gave up.

Still I have learned soooooo much about bikes and buell that whatever I invested in it already, was a tiny price to pay.

How much do you want for everything that is left?

_________________
08 Specialized Langster

Hi pash, I've pm-d you.

take care

Hi.

Is the engine available, or have I rushed the question before thoroughly reading the post?

Psycho.

Ill take the tail raise kit.if you could let me know how much?thanks

Tail kit is gone now, sorry. Engine wise, I have the cases and the gears + flywheel and pistons left. So not complete engine, sorry.

pm me if you need specific items or details please

Sorry about that guys, didn't expect such a barrage of messages I will update exactly what is left and what is not within a day or so.

Thanks for looking !

What exactly DID you expect then?

I suppose I'm glad to be disappointed

Ok, so far this is what is left (I may add other items if the arrangements I have with people fall through):

Engine cases with gears.
http://www.buellxb.com/buell_images/115 ... 0407_L.jpg

Flywheel (without the pinion gear)
http://www.buellxb.com/buell_images/115 ... 0331_L.jpg

Fuel pump
http://www.buellxb.com/buell_images/115 ... 0445_L.jpg

Carbon fibre airbox cover
http://www.buellxb.com/buell_images/115 ... 0541_L.jpg

Primary sprockets with chain
http://www.buellxb.com/buell_images/115 ... 0708_L.jpg

Rear pulley

air/fuel intake manifold with all the bits (both left and right injectors) fuel line connector.

airbox with K&N filter

rear swingarm with new oil drain plug and great condition oil lines connection bits

Front Yolks (top and bottom)

Rear foot pegs

Gear change and rear brake lever

Foot control thing that attaches to the frame both left and right

front break calliper

front and rear break discs

Oil cooler

Oil pump

oil cooler side oil lines

Rear exhaust attachment to the frame (crescent shaped thing) with 2 straps - brand new

Cam cover

timing cover with the timing thing

above mentioned gears all in perfect shape with all the rings and bits needed

clutch cable

front break lever with container and break line (OEM)

clutch lever

throttle cables

Stator

Wiring harness all the insulating tape taken off ready to be rewired. No connections changed yet comes with fuse box and ECM and cables marked with a marking sheet so it's clear where they need connecting.

Front fairing in carbon fibre

Oil pressure gauge (brand new)

neutral sensor

speedo sensor

HD (OEM) battery - still good, I ran it through a charger/condition checker and it's all green

K&N oil filter, unopened.

rear shock - complete and working (blue colour coding)

front and rear axles

foot stand

HD formula+ tranny oil (somehow sounds wrong )

ignition module

3 spark plugs (brand new)

horn

pushrods (4)

pushrod covers

pushrod rollers (between pushrods and cams - sorry don't know how to describe them better)

pulley Belt

belt tensioner

hand controls left and right (thortle side comes with handle)

speedo panel

oil cooler air scoop

engine fan

front and rear engine mounts

Harris rear paddock stand (designed specifically for buell's rear swingarm)

front paddock stand

Hydraulic bike lift (like the one in the link but blue) well used
http://www.google.co.uk/products/catalo ... ps-sellers


Buell bags
http://www.ebay.com/itm/saddle-bags-and ... 500wt_1287



If you buy a specific part I will include stainless screws/bolts with it as I have purchased a whole engine rebuild screw set.


Front forks and main frame are on ebay but if you can give me a good offer (with a small deposit) I can lift it from there. Frame comes with a V5 document, bike is sorned and no tax needed.



Sorry for a long post. Please pm me with items you want and prices you are offering (please research online/ebay prior to offering).

Kindest regards and thanks to everyone for viewing and interest

You really should keep the cam cover with the main crankcase ...they are line bored to suit so either without the other isn't really a good idea

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.

you speak wisely kevmean, I shall do that.