Stainless...
| UK Buell Enthusiasts Group https://ukbeg.com/forum/ |
|
| CR Rear footpeg hanger bolts. https://ukbeg.com/forum/viewtopic.php?f=11&t=23328 |
Page 1 of 1 |
| Author: | TheAlchemist [ 03 Aug 2018 23:27 ] |
| Post subject: | CR Rear footpeg hanger bolts. |
Hi All, Wanting to put the rear foot-peg hangers back on the CR, I am having a bit of an issue getting hold of the socket hex screws that bolt them on. Any one have 4 laying around, I believe they are 3/8-16 x 1 UNC. Or point me in the right direction.....UK I hope. Many thanks, Andy |
|
| Author: | pash [ 04 Aug 2018 08:34 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Riders of Bristol? |
|
| Author: | TheAlchemist [ 05 Aug 2018 21:53 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Thank you, Andy |
|
| Author: | Jazzbutcher [ 15 Aug 2018 00:35 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Hi there, I think you need some half inch spacers to go with them. 10-24 1/4 5/16 3/8 UNC Socket Cap Head Screws A2 Stainless Steel Imperial Bolts there are plenty, type that in Ebay Use stainless & copper grease them in. makes them easy to get back out. |
|
| Author: | Kiwi [ 15 Aug 2018 20:01 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Stainless...
|
|
| Author: | Kiwi [ 15 Aug 2018 20:02 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Jazzbutcher wrote: Hi there, I think you need some half inch spacers to go with them. 10-24 1/4 5/16 3/8 UNC Socket Cap Head Screws A2 Stainless Steel Imperial Bolts there are plenty, type that in Ebay Use stainless & copper grease them in. makes them easy to get back out. My original ones don't need spacers but the set that came with luggage do. FYI 
|
|
| Author: | TheAlchemist [ 15 Aug 2018 22:24 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Hi, Thank you, got the 1in long 3/8 in A2. Always use the copper grease. Anyhow they fit just right, no spacers straight in. The hanger casting is thick in the area the bolts pass through. Job done, my son will be happy now! Andy |
|
| Author: | Jazzbutcher [ 16 Aug 2018 11:15 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Nice one, Did you try those 3/8ths bolts in the front caliper mounts by any chance? I'm about to order some and I can't get my head round imperial bolt sizes. Thanks Paul |
|
| Author: | Bonzo [ 16 Aug 2018 11:49 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Jazzbutcher wrote: Nice one, Did you try those 3/8ths bolts in the front caliper mounts by any chance? I'm about to order some and I can't get my head round imperial bolt sizes. Thanks Paul They're the same, I once lost a front caliper bolt on the road (don't ask  ) and stuck one of the rear hanger bolts in its place.
|
|
| Author: | TheAlchemist [ 16 Aug 2018 21:05 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Hi Jazz, I have also got a few HT steel bolts of the same head and thread. If you PM me your address ill send them to you FOC as long as you are in the UK. Andy |
|
| Author: | Jazzbutcher [ 17 Aug 2018 00:28 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
That's very good of you, I can return the favour if you need any casing bolts in stainless? Thanks Paul |
|
| Author: | Adam [ 17 Aug 2018 13:27 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Jazzbutcher wrote: Nice one, Did you try those 3/8ths bolts in the front caliper mounts by any chance? I'm about to order some and I can't get my head round imperial bolt sizes. Thanks Paul Be very careful you don't get fobbed off with Whitworth bolts if you're after UNC. They will fit but the angle at the thread root is different by a few degrees. |
|
| Author: | TheAlchemist [ 17 Aug 2018 14:04 ] |
| Post subject: | Re: CR Rear footpeg hanger bolts. |
Bolts in the post, They are 3/8-16 x 1 UNC HT Steel. Andy |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|