UK Buell Enthusiasts Group
https://ukbeg.com/forum/

project tuber wanted
https://ukbeg.com/forum/viewtopic.php?f=11&t=24467		 Page 1 of 1
Author:  ferreteer [ 28 Jun 2020 22:08 ]
Post subject:  project tuber wanted
bloody hell it's been a long time since I gave up hope of finding a buell project.
Eventually, over an extended period, I started collecting tanks, seats and other stuff to customise my own m2 but....... I just cant' bring myself to do it. Orange and pewter should not be messed with so.....

I still need a project to play with in my retirement so I'm looking for the mankey-est cosmetically shite tuber out there. Doesn't even need a seat or tank or bars or much of anything as it will be a strip and rebuild job.

Would prefer not to do any piston/crank stuff but any other faults ok!!

PM me please, just so I can see it in my messages.

PS I may not even use one of my standard tanks because my pal has an english wheel and he has offered to do a one off tank for me for the cost of the sheet!

Come on chaps get your thinking caps on!
Author:  TOPGUMM [ 29 Jun 2020 00:13 ]
Post subject:  Re: project tuber wanted
10,000 mile S1 1998 in siver Good con £4K

Start with a better option than a shitter.
Author:  ferreteer [ 29 Jun 2020 19:35 ]
Post subject:  Re: project tuber wanted
TOPGUMM wrote:
10,000 mile S1 1998 in siver Good con £4K

Start with a better option than a shitter.



:ner: :4roz: :coat:
Author:  TOPGUMM [ 29 Jun 2020 20:41 ]
Post subject:  Re: project tuber wanted
:shock: :shock: :shock: :shock: :shock:

Good luck with a project for cost .
lOl
Author:  ferreteer [ 29 Jun 2020 23:35 ]
Post subject:  Re: project tuber wanted
TOPGUMM wrote:
:shock: :shock: :shock: :shock: :shock:

Good luck with a project for cost .
lOl


One of the most important lessons my teachers taught me at school was always read the question and make sure you understand it before answering or you will certainly lose marks💃❤️🙊.

Hells bells man, you even got the bit wrong about PMIng me so I got an alert in my email without having to constantly refer back to the thread. :headbang: :rotfl:
Author:  pash [ 30 Jun 2020 05:17 ]
Post subject:  Re: project tuber wanted
Perish the thought of having to come back to the forum to look at replies to your own post...
Author:  TOPGUMM [ 30 Jun 2020 10:53 ]
Post subject:  Re: project tuber wanted
pash wrote:
Perish the thought of having to come back to the forum to look at replies to your own post...


Think I`ll PM ferret to annoy him .

Also what time is 5.17 to be up in the morning posting on here , (pm me about it )
Author:  ferreteer [ 30 Jun 2020 14:02 ]
Post subject:  Re: project tuber wanted
TOPGUMM wrote:
Think I`ll PM ferret to annoy him ....


Except you didn't PM me... you took the opportunity, again, to grandstand your rhetoric on open forum. Thank you for another flash of your psychometrics! :uhoh:

Jeeeeez :4roz:
Author:  TOPGUMM [ 30 Jun 2020 14:09 ]
Post subject:  Re: project tuber wanted
piss off
Author:  ferreteer [ 30 Jun 2020 16:53 ]
Post subject:  Re: project tuber wanted
pash wrote:
Perish the thought of having to come back to the forum to look at replies to your own post...



"Did you cut two slices of batten-burg or only one?" Well to tell you the truth in all this excitement I kinda lost track myself. But being this is a marzipan, 4 core jammy delight, the most powerful desert cake in the world and would blow your head clean off, you've gotta ask yourself one question: "Do I feel lucky?" Well, do ya, punk?

xxxxx :ner:
Author:  pash [ 30 Jun 2020 21:11 ]
Post subject:  Re: project tuber wanted
TOPGUMM wrote:
pash wrote:
Perish the thought of having to come back to the forum to look at replies to your own post...


Think I`ll PM ferret to annoy him .

Also what time is 5.17 to be up in the morning posting on here , (pm me about it )

I PMed you
Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/