| UK Buell Enthusiasts Group https://ukbeg.com/forum/ |
|
| Stainless bolts https://ukbeg.com/forum/viewtopic.php?f=7&t=11413 |
Page 1 of 1 |
| Author: | valerian [ 22 Jun 2011 20:51 ] |
| Post subject: | Stainless bolts |
what stainless bolt kits can i get for my 2006 ulysses and also will i be able to replace the torx ones with sumat decent cheers |
|
| Author: | Ash [ 22 Jun 2011 21:07 ] |
| Post subject: | Re: Stainless bolts |
Ebay is always good, these are for an 07 and I'm not entirely sure they are all the same , someone will be along shortly to say either way but its worth contacting the seller if not ... http://cgi.ebay.co.uk/Buell-XB12S-07-XB ... 3cad1de691 |
|
| Author: | sillyb [ 22 Jun 2011 22:43 ] |
| Post subject: | Re: Stainless bolts |
Do you know where i could get same kit for X1, did put post on here a while ago but got no response. Any help would be appreciated. |
|
| Author: | Adam [ 22 Jun 2011 23:09 ] |
| Post subject: | Re: Stainless bolts |
sillyb wrote: Do you know where i could get same kit for X1, did put post on here a while ago but got no response. Any help would be appreciated. If you do a search, I think there's a list somewhere in the archives. I think CJ posted it some time ago 
|
|
| Author: | kevmean [ 22 Jun 2011 23:12 ] |
| Post subject: | Re: Stainless bolts |
valerian wrote: what stainless bolt kits can i get for my 2006 ulysses and also will i be able to replace the torx ones with sumat decent cheers Torx are actually a lot better than allen head  just make sure you use a good quality bit and make sure the same as with allen head that the bit is fully engaged in the bolt head.Adam will probably be along to tell you his trick of using a dab of grinding paste on the end of the bit to stop it slipping out 
|
|
| Author: | kevmean [ 22 Jun 2011 23:12 ] |
| Post subject: | Re: Stainless bolts |
Wow ....he didn't mention it
|
|
| Author: | CJ [ 23 Jun 2011 07:13 ] |
| Post subject: | Re: Stainless bolts |
These are the lists for my Buells, 1997 S1 and 2008 spec XB12X. I didn't buy them as ready made kits but bought them loose and fitted them over a period of time. I used my local stockist shown below but other suppliers are available: D MIDDLETON UNIT 5 LADY ANNE MILLS BATLEY WEST YORKS WF17 0PS TEL 01924 470807 FAX 01924 470764 WEB SITE: http://WWW.STAINLESSMIDDLETON.CO.UK 2008 SPEC BUELL ULYSSES XB12X ALL SOCKET HEAD CAP SCREWS UNLESS STATED OTHERWISE --------------------------------------------------------------------------------- 1203cc BUELL THUNDERSTORM (2008 SPEC) ENGINE FASTENERS 'THUNDERSTORM COVER' RIGHT HAND SIDE OF ENGINE - STANDARD BLACK JAPANNED 4 OFF 1/4"UNC X 1" LONG (9 TO 12.4NM) 3 OFF 1/4"UNC X 3" LONG (9 TO 12.4NM) 7 OFF 1/4" X 7/16" SMALL OD WASHERS RIGHT HAND CASE - STANDARD BLACK JAPANNED 4 OFF 1/4"UNC X 1" LONG (9 TO 12.4NM) 4 OFF 1/4" X 7/16" SMALL OD WASHERS PRIMARY CHAINCASE - STANDARD BLACK JAPANNED 13 OFF 1/4"UNC X 2" LONG (9 TO 12.4NM) 13 OFF 1/4" X 7/16" SMALL OD WASHERS BASE OF PUSHROD TOWERS - STANDARD BLACK JAPANNED 8 OFF 3/16"UNC X 3/4" LONG (4 PER TOWER) 8 OFF 3/16" WASHERS (4 PER TOWER) --------------------------------------------------------------------------------- OIL COOLER PLASTIC 'AIR SCOOP' 2 OFF 1/4"UNC X 1/2" LONG 2 OFF 1/4" X 7/16" SMALL OD WASHERS OIL COOLER FRONT MOUNT 2 OFF 1/4"UNC X 3/4" LONG (10NM) 2 OFF 1/4" X 7/16" SMALL OD WASHERS HANDGUARDS - LEFT AND RIGHT 4 OFF M5 X 16 (2 EACH SIDE) 4 OFF M5 WASHERS (2 EACH SIDE) LEFT HAND SWITCH BLOCK 2 OFF M5 X 25 RIGHT HAND SWITCH BLOCK 1 OFF M5 X 25 1 OFF M5 X 40 LEFT HAND MIRROR MOUNT CLAMP 1 OFF M6 X 20 (8NM) RIGHT HAND MIRROR/FRONT BRAKE RESERVOIR MOUNT CLAMP 2 OFF M6 X 20 (8NM) FRONT FORK LOWER PINCH BOLTS 4 OFF 5/16"UNC X 1" LONG (27 TO 30NM) (2 PER FORK) FRONT FORK UPPER PINCH BOLTS 2 OFF 3/8"UNC X 1" LONG (31 TO 34NM) (1 PER FORK) STEERING STEM PINCH BOLT 1 OFF 5/16"UNC X 1" LONG (27 TO 30NM) HANDLEBAR CLAMP BOLTS 4 OFF 5/16"UNC X 1" LONG (14 TO 16NM) (TIGHTEN FRONT BOLTS TO CORRECT TORQUE FIRST AND THEN THE REAR BOLTS) FOOTREST MOUNTING BRACKETS - LEFT AND RIGHT 6 OFF 1/4"UNC X 3/4" LONG (15 TO 16NM) (3 EACH SIDE) REDUNDANT FAIRING SUPPORT BRACKET - FRONT OF STEERING HEAD/FRAME, BEHIND HEADLIGHTS 2 OFF M8 X 70 C/W 4 OFF M8 WASHERS AND 2 OFF M8 NYLOCK NUTS. (THESE REPLACE THE STANDARD 5/16"UNC X 3" LONG BOLTS) REAR OF FRONT MUDGUARD 4 OFF 1/4"UNC X 3/4" LONG (2 EACH SIDE) 4 OFF 1/4" X 5/8" LARGE OD WASHERS (2 EACH SIDE) THE STANDARD FRONT TORX T27 FASTENERS ARE STAINLESS AND HAVE A SHOULDER ON THEM. UNDER ENGINE CHIN SPOILER THE STANDARD TORX T27 FASTENERS ARE STAINLESS AND HAVE A SHOULDER ON THEM. RIGHT HAND FRONT PULLEY COVER 1 OFF 1/4"UNC X 1 1/2" LONG 1 OFF 1/4" X 7/8" LARGE OD WASHER 2 OFF 1/4"UNC X 3/4" LONG 2 OFF 1/4" X 5/8" LARGE OD WASHERS REAR HUGGER 3 OFF 1/4"UNC X 1/2" LONG (HEX HEAD) 2 OFF 1/4"UNC X 1/2" LONG (SKT HEAD CAP) 5 OFF 1/4" X 5/8" LARGE OD WASHERS BOTTOM BELT GUARD 2 OFF 1/4"UNC X 1/2" LONG 2 OFF 1/4" X 5/8" LARGE OD WASHERS ENGINE COOLING AIR SCOOPS - LEFT AND RIGHT 6 OFF 1/4"UNC X 1/2" LONG (3 EACH SIDE) 6 OFF 1/4" X 5/8" LARGE OD WASHERS (3 EACH SIDE) NOTE: THE UNDER SEAT AREA USES A MIXTURE OF 1/4"UNC FASTENERS BUT I DON'T KNOW WHAT THE STANDARD LENGTHS ARE. MY BIKE HAS TOURATECH PANNIER BRACKETS FITTED SO USES NON STANDARD FASTENERS. 1203cc BUELL ENGINE FASTENERS - 1997 S1 LIGHTNING ROCKER BOX COVER - PER CYLINDER 4 OFF 1/4"UNC X 7/8" LONG (14 TO 18NM) 4 OFF 1/4" X 5/8" LARGE OD WASHERS 4 OFF 63858-49 FIBRE WASHERS (BUELL PART) BOTTOM OF PUSH ROD TUBES - PER CYLINDER 2 OFF 5/16"UNC X 3/4" LONG (20 TO 24NM) 2 OFF 5/16" X 1/2" SMALL OD WASHERS 1 OFF 1/4"UNC X 7/8" LONG (9 TO 12.4NM) 1 OFF 1/4" X 7/16" SMALL OD WASHER TIMING GEAR CASE 1 OFF 1/4"UNC X 1 1/4" LONG (9 TO 12.4NM) 3 OFF 1/4"UNC X 1 3/4" LONG (9 TO 12.4NM) 2 OFF 1/4"UNC X 2" LONG (9 TO 12.4NM) 5 OFF 1/4"UNC X 2 1/4" LONG (9 TO 12.4NM) 11 OFF 1/4" X 7/16" SMALL OD WASHERS PRIMARY CHAINCASE 7 OFF 1/4"UNC X 1 3/4" LONG (9 TO 12.4NM) 4 OFF 1/4"UNC X 2 1/4" LONG (9 TO 12.4NM) 2 OFF 5/16"UNC X 3 1/2" LONG (9 TO 12.4NM) 11 OFF 1/4" X 7/16" SMALL OD WASHERS 2 OFF 5/16" X 1/2" SMALL OD WASHERS CLUTCH (DERBY) INSPECTION COVER 4 OFF 1/4"UNC X 5/8" LONG BUTTON SOCKET SCREWS (9 TO 12NM) 4 OFF 1/4" X 7/16" SMALL OD WASHERS PRIMARY CHAIN INSPECTION COVER 2 OFF 1/4"UNC X 9/16" LONG COUNTERSUNK SOCKET SCREWS (4.5 TO 6.8NM) (USE 3/4" LONG CUT DOWN - WHICH ARE MORE READILY AVAILABLE) |
|
| Author: | restone [ 23 Jun 2011 21:10 ] |
| Post subject: | Re: Stainless bolts |
Thanks for the lists CJ ...... I've always used Custom Fasteners to get all my stainless bits from. Very reliable, knowledgeable and stuff always turns up next day in the post, well recommended 
|
|
| Author: | Adam [ 23 Jun 2011 22:54 ] |
| Post subject: | Re: Stainless bolts |
The bloke that owns Custom Fasteners (name escapes me now  ) was a drag racer of some repute during the Brit twin 'Hog Slayer' era, and certainly knows his stuff - even if he is a bit miserable I'm not a great fan of stainless fasteners, but I am of Torx heads (the Buell std ones are fine even if the heads get to look a bit scruffy) but you'll find everything you want at the 2 Stafford Classic Bike shows. Even the auto jumble there turns up with all kinds of exotic UNF/UNC aerospace quality bolts, with all sorts of different heads.
|
|
| Author: | zoidberg [ 23 Jun 2011 23:31 ] |
| Post subject: | Re: Stainless bolts |
just coppaslip them before they go in. |
|
| Author: | Maz [ 24 Jun 2011 00:03 ] |
| Post subject: | Re: Stainless bolts |
 ......I hate SS fasteners 
|
|
| Author: | chris(madrid) [ 24 Jun 2011 09:38 ] |
| Post subject: | Re: Stainless bolts |
Maz wrote: :yt: ......I hate SS fasteners There was a time you supplied them though. One has some SS bolts sir supplied affixing his derby cover. 
|
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|