UK Buell Enthusiasts Group
https://ukbeg.com/forum/

S1 missing spar
https://ukbeg.com/forum/viewtopic.php?f=7&t=19506		 Page 1 of 2
Author:  DaveH [ 20 Oct 2014 09:39 ]
Post subject:  S1 missing spar
So this winter it's the turn of the frame on my s1W for modifying. It's nearly ready to lift off. The rear footrest loops are for the chop, the redundant oil tank bracket on the back of the battery plate, thats going too, and the missing frame spar is to be welded in. To the people who have done this, what grade tubing have you used. I don't want to use red band seamed pipe, it's shite to weld spitting everywhere, nasty stuff. Any Info or direction greatly received.......DaveH
Author:  pash [ 20 Oct 2014 11:06 ]
Post subject:  Re: S1 missing spar
Not the rear footrests!!!
Author:  Adam [ 20 Oct 2014 11:36 ]
Post subject:  Re: S1 missing spar
I did one for a mate who was tarting up his S1 some years ago. He brought me a section of Renolds 631 that he'd cut out from a rear wheel triangle of a push bike frame lOl
He wanted me to braze it in, but not wanting to put a lot of heat into the Buell frame tubing, I decided to Tig it with some mild steel rod.
I don't have a tube notcher and it took ages with a half round file getting a precision fit - finding someone with a 'notcher' will make life a lot easier :yup:
Author:  pash [ 20 Oct 2014 11:39 ]
Post subject:  Re: S1 missing spar
I used a half round file on mine and it was TIGged in.

Not sure what the spec was but I'll try and find out later.
Author:  rik [ 20 Oct 2014 14:29 ]
Post subject:  Re: S1 missing spar
Buy this, chop out that bit at the bottom, and be 100% confident that it's the correct gauge...





:coat:
Author:  x1glider [ 20 Oct 2014 16:18 ]
Post subject:  Re: S1 missing spar
Dave, Buell used 4130 CrMo on all 96 and later tube frames, AISI 1018 before that. Can't recall the tubing size but you'll figure it out when you cut into it.
Author:  DaveH [ 21 Oct 2014 11:09 ]
Post subject:  Re: S1 missing spar
Thanks all. Bob that info was just what i was after :yup: . Even found a place in the UK that sells it by the ft and a nice little video on youtube on hints and tips on welding it and what rods to use. :D
Author:  x1glider [ 21 Oct 2014 17:53 ]
Post subject:  Re: S1 missing spar
DaveH wrote:
Thanks all. Bob that info was just what i was after :yup: . Even found a place in the UK that sells it by the ft and a nice little video on youtube on hints and tips on welding it and what rods to use. :D

Even though it's an under-match for 4130, most manufacturers of frames and chassis use ER70S-2 as the frames are typically normalized tubing. NASCAR (Septic left-turn racing) requires it since they mix 4130 and 1018. It's a less liquid weld pool than ER80S-D2 so it's good for vertical and overhead positions and doesn't require post-heat treatment.
Author:  Jim [ 22 Oct 2014 18:40 ]
Post subject:  Re: S1 missing spar
Got rid of the whole seat unit frame and foot rests on mine. Looks loads better. Still working on the fecker tho!
Author:  DaveH [ 12 Nov 2014 19:39 ]
Post subject:  Re: S1 missing spar
Well the frame was off and in my hands tonight. Christ those isolator cap heads were
tight, i nearly burst a blood vessel, and the frame was heavier than i thought considering it's made from chromo, though there is a raft of brackets and gussets. It'll be lighter once the angle grinder's been in action :twisted:
Author:  pash [ 12 Nov 2014 19:53 ]
Post subject:  Re: S1 missing spar
Aaaaaaarrrrrrrrrggggggghhhhhhh
Author:  Maz [ 12 Nov 2014 19:54 ]
Post subject:  Re: S1 missing spar
:eat:
Author:  gusm2 [ 12 Nov 2014 20:10 ]
Post subject:  Re: S1 missing spar
Interesting :!:
Author:  DaveH [ 12 Nov 2014 20:10 ]
Post subject:  Re: S1 missing spar
worry not pash. It'll all be done in the best possibe taste http://www.youtube.com/watch?v=5h8tQJHUuuo
Author:  pash [ 12 Nov 2014 20:14 ]
Post subject:  Re: S1 missing spar
Not the rear pegs... Please...
Page 1 of 2 All times are UTC
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/