UK Buell Enthusiasts Group
https://ukbeg.com/forum/

X1 Tail tidy???
https://ukbeg.com/forum/viewtopic.php?f=7&t=8332		 Page 1 of 2
Author:  penndino [ 09 Sep 2010 00:50 ]
Post subject:  X1 Tail tidy???
want to get rid of original undertray and no. plate holder..any good ones out therefor a nice sleak finish..pics would be a help..CHEERS!!!!!!!!!
Author:  Trojan [ 09 Sep 2010 09:19 ]
Post subject:  Re: X1 Tail tidy???
There used to be a few on the market for an X1 from Ermax and a few other small Buell specialists in Europe. Unfortunately as far as I know almost all of these have been discontinued now.

The only one left that we can still get is the RRC tail tidy pictured below.

Image

Price for this piece is £134.60 inc VAT and you can order them here http://www.trojan-horse.co.uk/prods/417.html

We only get them in to order so this can take 3-4 weeks I'm afraid.

You may still be able to find one of the discontinued items on Ebay of course.
Author:  Adam [ 09 Sep 2010 17:00 ]
Post subject:  Re: X1 Tail tidy???
:yt: Both of my complete X1s have then knocked up from some ally plate I had knocking around. Costs nowt except a couple of hours of your time. You can relocate your seat lock somewhere out of sight too.
Author:  Nutah [ 09 Sep 2010 19:45 ]
Post subject:  Re: X1 Tail tidy???
:yt:
as Adam says

Greasemonkey's however is a work of art :worthy:
Author:  Adam [ 09 Sep 2010 20:22 ]
Post subject:  Re: X1 Tail tidy???
Nutah wrote:
:yt:
as Adam says

Greasemonkey's however is a work of art :worthy:



:yt: He's even got a smoke grenade launcher fixed underneath lOl
Author:  penndino [ 14 Sep 2010 00:57 ]
Post subject:  Re: X1 Tail tidy???
greasemonkey wrote:
if you're handy with a blowlamp an' panel hammer Penndino, you could have a go at your own :idea:
Image

,,tidys up the arse end somewhat
Image

right it's hammer time!!! can't find anything to buy so going to have a go!!!
Author:  Adam [ 14 Sep 2010 07:25 ]
Post subject:  Re: X1 Tail tidy???
If you're going to do some metal battering, do it on a bag of wet sand ;)
Author:  Nutah [ 14 Sep 2010 21:00 ]
Post subject:  Re: X1 Tail tidy???
greasemonkey wrote:
maybe so, but yours takes the tight-arse ingenuity award hands down lOl


http://s726.photobucket.com/albums/ww26 ... ics055.jpg

:couch:
Author:  Adam [ 14 Sep 2010 21:44 ]
Post subject:  Re: X1 Tail tidy???
greasemonkey wrote:
don't confuse the lad Adam, it'll take the heat out the plate ;)



I've just got access to the local FE College fabrication workshop and it would make you cry if you went around. They've got a huge surface plate table, that some little scrote has been stick welding on :x and various other bits of quality gear that's been mindlessly played with - usually smacked with a hammer :roll: - etc, etc.
They've also got an English wheel and unlimited sheet steel to play with, I had to tell two Lecturers what it was for and show another one how to use it. What a lovely bit of kit it is 8-) I've always wanted one of those 8-) :geek:

It really does worry me about where this Country is going to get its next generation of Engineers from; proper ones, that can use their brain and are able to fabricate stuff as well.
God bless Fred Dibnah 8-)
Author:  penndino [ 14 Sep 2010 22:55 ]
Post subject:  Re: X1 Tail tidy???
don't be too down beat there is still enough nutters in sheds to keep the spirit alive!!
Author:  Adam [ 15 Sep 2010 20:47 ]
Post subject:  Re: X1 Tail tidy???
Scraping, now there's another lost art. My Dad would never chuck away an old file (ended up with a drawer full of them lOl :roll: ) incase he needed to make a new scraper. How many people can still carry out the art of it? Not many, I suspect :roll:
Page 1 of 2 All times are UTC+01:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/