2003 ECM
2005/2006/2007 ECM (two different sets of calibration)
| UK Buell Enthusiasts Group https://ukbeg.com/forum/ |
|
| fire bolt ecm https://ukbeg.com/forum/viewtopic.php?f=8&t=15183 |
Page 1 of 2 |
| Author: | moogymus668310 [ 05 Aug 2012 23:55 ] |
| Post subject: | fire bolt ecm |
can anybody enlighten me . my fire bolt that i am putting together from a box of bits has an ECM with 1 grey multi connector and 1 black multi connector , no problem there then like to like . but between them is a single spade terminal and i don't appear to have a corresponding spade connector . some ecm i have seem have it some don't , can anybody shed some light on this for me . or am i missing something . best regards findlay |
|
| Author: | gunter [ 06 Aug 2012 04:41 ] |
| Post subject: | Re: fire bolt ecm |
Exhaust valve motor is connected there. 2002 and 2003 models had an ECM with no connector between the sockets, as XB9 do not have the exhaust valve motor installed. |
|
| Author: | pash [ 06 Aug 2012 05:59 ] |
| Post subject: | Re: fire bolt ecm |
I think the spade connector is on both 9 and 12 harnesses from 2004 onwards but the 3 pin Deutsch connector under the seat, which connects to the motor, has a rubber bung fitted on the 9. I am guessing your ECM and harness are not the correct match, the injectors changed in 2004 (they became directional and squirted down the port rather than on the manifold wall) and the CB060 (early) and GB231/IB310 (later) have different maps to match. Either will work, the AFV will compensate. What year is your bike? |
|
| Author: | moogymus668310 [ 06 Aug 2012 19:19 ] |
| Post subject: | Re: fire bolt ecm |
the xb9r i have is a 2002 modle on a 2003 plate |
|
| Author: | pash [ 06 Aug 2012 19:23 ] |
| Post subject: | Re: fire bolt ecm |
Is there anything written in the ECM? BUEGB231 or BUEIB310? |
|
| Author: | gunter [ 06 Aug 2012 19:45 ] |
| Post subject: | Re: fire bolt ecm |
2002 model ECM: http://i.ebayimg.com/t/Buell-XB12-Stand ... g~~_12.JPG 2004 model ECM: http://www.motorrad-technik-maass.de/mt ... p=1224_060 couldn't find a 2003 model ECM, looks like a 2002 one, but bottom label ends with "CB060" instead of "CB050". |
|
| Author: | pash [ 06 Aug 2012 20:09 ] |
| Post subject: | Re: fire bolt ecm |
2003 ECM 2005/2006/2007 ECM (two different sets of calibration)
|
|
| Author: | moogymus668310 [ 06 Aug 2012 22:16 ] |
| Post subject: | Re: fire bolt ecm |
the ECM has two bar codes on it with the following numbers on a green background No326 IRA 04081 BX1EC21 GB 231 and 496 on the black socket does this help |
|
| Author: | pash [ 06 Aug 2012 22:29 ] |
| Post subject: | Re: fire bolt ecm |
Yeah, tis a 2004 ECM |
|
| Author: | shellfin [ 06 Aug 2012 22:39 ] |
| Post subject: | Re: fire bolt ecm |
  
|
|
| Author: | moogymus668310 [ 06 Aug 2012 22:45 ] |
| Post subject: | Re: fire bolt ecm |
so it should work i think |
|
| Author: | pash [ 06 Aug 2012 22:48 ] |
| Post subject: | Re: fire bolt ecm |
Yes but the AFV will look funny cos it is meant to run with different injectors. Ideally you want a 2002 ECM... |
|
| Author: | moogymus668310 [ 06 Aug 2012 22:59 ] |
| Post subject: | Re: fire bolt ecm |
not totaly on top of this what does AFV stand for . so should i source a 2002 ECM |
|
| Author: | shellfin [ 06 Aug 2012 23:04 ] |
| Post subject: | Re: fire bolt ecm |
these pictures are from moogymus668310 firebolt |
|
| Author: | pash [ 06 Aug 2012 23:06 ] |
| Post subject: | Re: fire bolt ecm |
Was the ECM fitted to the bike ever? It is not the correct ECM for the year of engine (it could actually be one from a 12). It will have maps in with a shorter injector duration to work with higher flow injectors. You will probably need to do a TPS reset anyway, whilst you are at it you could load some new maps which I can send you, to work better with your injectors. But yes it will work, assuming it came off a 9... |
|
| Page 1 of 2 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|