Quote:
checked the tps and there no adjustment on it
| UK Buell Enthusiasts Group https://ukbeg.com/forum/ |
|
| xb12s running rough https://ukbeg.com/forum/viewtopic.php?f=8&t=2948 |
Page 1 of 1 |
| Author: | rjk1188 [ 10 Oct 2009 16:35 ] |
| Post subject: | xb12s running rough |
new owner of the above, i think it is a fueling problem, when engine is up to temp i blip the throttle and doesn't do any thing for a split sec, also with the throttle on the smallest of opening the engine rev's aren't steady, surging from 1500 to 2000 rpm, it's got an after market can on, make unknown, and the cable is disconnented on top of air filter, checked the tps and there no adjustment on it, any help please,rick, |
|
| Author: | THE FLYING DUCHMAN [ 10 Oct 2009 17:29 ] |
| Post subject: | Re: xb12s running rough |
What reg is the bike and how many miles on it. |
|
| Author: | rjk1188 [ 10 Oct 2009 18:49 ] |
| Post subject: | Re: xb12s running rough |
53 plate 6200 miles, |
|
| Author: | Maz [ 10 Oct 2009 19:09 ] |
| Post subject: | Re: xb12s running rough |
Quote: checked the tps and there no adjustment on it
|
|
| Author: | rjk1188 [ 10 Oct 2009 19:17 ] |
| Post subject: | Re: xb12s running rough |
the holes in the tps where the two little 7mm screws/bolt's that go through to bolt it on the tb are the same size as bolt's, there not elongated, it fixed in one place |
|
| Author: | pash [ 10 Oct 2009 19:19 ] |
| Post subject: | Re: xb12s running rough |
Have you done this? viewtopic.php?f=17&t=13 |
|
| Author: | Maz [ 10 Oct 2009 19:20 ] |
| Post subject: | Re: xb12s running rough |
I'm thinking the obvious answer to that Pash, is no  
|
|
| Author: | rjk1188 [ 10 Oct 2009 19:31 ] |
| Post subject: | Re: xb12s running rough |
thanks, were can i buy this ecmspy diagnostics stuff from, any were in the uk? supply it, or from the usa |
|
| Author: | THE FLYING DUCHMAN [ 10 Oct 2009 19:35 ] |
| Post subject: | Re: xb12s running rough |
rjk1188 wrote: the holes in the tps where the two little 7mm screws/bolt's that go through to bolt it on the tb are the same size as bolt's, there not elongated, it fixed in one place Ok Rick. Do NOT do anything else on your bike for the moment because you could do more harm than good. Without wishing to sound rude it is clear you do not know how the systems on a Buell work. Like the man said read up and find out all you can. Help is here if you need it. It might be best to get a dealer to do the TPS this time around. Using ECM-Spy, if you do not know the bike, could be a problem. |
|
| Author: | rjk1188 [ 10 Oct 2009 19:50 ] |
| Post subject: | Re: xb12s running rough |
thank, do you now of any dealers in the devon, south west? that wont rip me off, or any members around this area that could help, thanks again,rick, |
|
| Author: | pash [ 10 Oct 2009 20:01 ] |
| Post subject: | Re: xb12s running rough |
Come visit me in Bristol if you like... Tea and biscuits await...  Your bike may run rough, but, if the reason is the TPS being out, you can still ride it safely... |
|
| Author: | rjk1188 [ 10 Oct 2009 20:47 ] |
| Post subject: | Re: xb12s running rough |
http://cgi.ebay.com/ebaymotors/Buell-EC ... 23032f4e1b is this what i need? |
|
| Author: | pash [ 10 Oct 2009 22:13 ] |
| Post subject: | Re: xb12s running rough |
Yeah, but you can make your own for less... http://www.ecmspy.com/kabel_pc.shtml |
|
| Author: | Lands End [ 20 Oct 2009 21:47 ] |
| Post subject: | Re: xb12s running rough |
Or send me a PM, I'm down at Lands End, (Obviously)!  I could even meet you half way or sommat?
|
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|