Thanks for that.
Good to see you back on the forum gt85.
| UK Buell Enthusiasts Group https://ukbeg.com/forum/ |
|
| Do you remember... https://ukbeg.com/forum/viewtopic.php?f=8&t=968 |
Page 1 of 1 |
| Author: | iwoo9 [ 10 Jun 2009 13:45 ] |
| Post subject: | Do you remember... |
On the last message board someone posted a list of tools required to fettle a Buell. I'm looking at CJ on this one, as he is a fan of all things list like. I have been back to look and couldn't find the post. Failing that: has anybody got a list of tools that I need to keep the X1 in one piece? |
|
| Author: | gt85 [ 10 Jun 2009 14:35 ] |
| Post subject: | Re: Do you remember... |
Hello...been a long time since i've posted and feels even longer from when i sold my bike. CJ did indeed post a list of torques....i did a short list of essential tools needed for the job but I don't know where it has now gone. I'm sure someone will post some info later however the main tools you need is a AF (American Fine) set of sockets & bits (Teng tools do a set covering all the sizes for £40) + a good ratchet + possibly 2 torque wrenches one from 10nm-40nm and another from 40nm-100nm. |
|
| Author: | iwoo9 [ 11 Jun 2009 09:57 ] |
| Post subject: | Re: Do you remember... |
Thanks for that. Good to see you back on the forum gt85.
|
|
| Author: | gt85 [ 11 Jun 2009 13:38 ] |
| Post subject: | Re: Do you remember... |
iwoo9 wrote: Thanks for that. Good to see you back on the forum gt85. Yeah although, without a bike, i feel like my bollocks have been cut off... |
|
| Author: | pash [ 11 Jun 2009 13:39 ] |
| Post subject: | Re: Do you remember... |
iwoo9 wrote: Thanks for that. Good to see you back on the forum gt85. 
|
|
| Author: | beanie [ 12 Jun 2009 22:12 ] |
| Post subject: | Re: Do you remember... |
OK call me thick (and I know you all will) but I was always told that AF was across flat...standing by for someone to correct me 
|
|
| Author: | Adam [ 12 Jun 2009 22:29 ] |
| Post subject: | Re: Do you remember... |
beanie wrote: OK call me thick (and I know you all will) but I was always told that AF was across flat...standing by for someone to correct me I've always known it as that as well. However, I believe the other definition is also correct 
|
|
| Author: | Maz [ 12 Jun 2009 23:19 ] |
| Post subject: | Re: Do you remember... |
American fine describes a thread pitch, AF in relation to tools is indeed 'across flats' and is normally applied to imperial stuff, although a 13mm spanner could accurately be described as 13mm AF, as in across flats. |
|
| Author: | muzza [ 17 Jun 2009 18:07 ] |
| Post subject: | Re: Do you remember... |
there is usally a guy on ebay selling a set from the states, they bid for silly money but if you write to him you can buy now for £25 delivered! |
|
| Author: | chris_sheena [ 17 Jun 2009 20:01 ] |
| Post subject: | Re: Do you remember... |
and they are shit got a set and as the old saying goes buy cheap buy twice |
|
| Author: | Ash [ 17 Jun 2009 20:19 ] |
| Post subject: | Re: Do you remember... |
Have you tried the archive section of this forum followed by the search function of the next .... ? not being a PiTA but it is still there somewhere ... |
|
| Author: | iwoo9 [ 18 Jun 2009 09:11 ] |
| Post subject: | Re: Do you remember... |
Ash wrote: Have you tried the archive section of this forum followed by the search function of the next .... ? not being a PiTA but it is still there somewhere ... I did try that before I posted. It's a day or two since I posted but it seemed that my search terms either generated zero responses or hundreds. I did wade through the list generated in response to the word 'tools' but couldn't find what I was looking for. That's when I thought I'd use some of the smarter computers (you lot) to speed up my search of the TOM (aka computer aka Totally Obedient Moron). |
|
| Page 1 of 1 | All times are UTC |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|