It is currently 05 Dec 2024 15:48

All times are UTC




Post new topic  Reply to topic  [ 28 posts ]  Go to page Previous 1 2
Author Message
PostPosted: 17 Jul 2012 10:38 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Exhaust is standard.
So I continue to try to undo the hex bolt, not the nut on the other side then?
Counterclockwise to loosen?


Top
PostPosted: 17 Jul 2012 19:33 
Offline
proff. patpending
User avatar

Joined: 06 May 2009 20:20
Posts: 14705
Current ride: Victoria Sponge
Location: Bristol - Gateway to all things good
Yep, anti clockwise to undo.

Might be worth giving Baz a ring at Lightning Services as they put it together (think it was actually Thorkill the Tall on this forum) to see if they did anything special that is giving you trouble.

_________________
08 Specialized Langster


Top
PostPosted: 18 Jul 2012 08:12 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Thanks for the info, email sent to him, but been a while since he's been on by the the looks...


Top
PostPosted: 03 Aug 2012 17:04 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Bolt now out, local bike shop unable to do so 'specialist' came to house & did it.
Now, how do I keep the new nut 'captive' whilst I screw in the bolt from the other side as it keeps pushing it out as I screw it in....the recess for the shoulders of the bolt aren't that proud to hold it... Bit of araldite? :?


Top
PostPosted: 03 Aug 2012 23:15 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
I meant the recess for the shoulders of the nut, not the bolt.......
Any ideas? :?:


Top
PostPosted: 04 Aug 2012 19:20 
Offline
User avatar

Joined: 08 May 2009 13:13
Posts: 3651
Current ride: XB9SX
birdy wrote:
I meant the recess for the shoulders of the nut, not the bolt.......
Any ideas? :?:


I just hold the nut in place with a screw driver and simultaniously feed the bolt in using a hex bar. After you have slid the new strap through the bracket that is. The clamp and nut to the strap go on the left side of the bike. ;)


Top
PostPosted: 04 Aug 2012 22:34 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Cheers ed; long arms needed to hold both the nut and screw the hex bolt or did you wedge the screwdriver? :|


Top
PostPosted: 04 Aug 2012 22:39 
Offline
Resident Bender
User avatar

Joined: 20 Sep 2009 19:28
Posts: 1601
Current ride: EBR 1190RX
Location: banbury uk
:?

_________________
Buell X1
Buell xb12s
Buell 1125r
Ebr 1190rx
Bimota Db7
Norton v4rr??



http://www.aph-performance-engineering.com


Top
PostPosted: 04 Aug 2012 23:25 
Offline
User avatar

Joined: 08 May 2009 13:13
Posts: 3651
Current ride: XB9SX
birdy wrote:
Cheers ed; long arms needed to hold both the nut and screw the hex bolt or did you wedge the screwdriver? :|


I may have used my fingers and probably sat on the floor under the bike while it was on a paddock stand, but it's been a while since that bracket came off mine. Welcome to Buell ownership. :?

Treat new bolt with copper grease and do not overtighten straps. ;)


Top
PostPosted: 04 Aug 2012 23:50 
Offline
User avatar

Joined: 08 May 2009 13:13
Posts: 3651
Current ride: XB9SX
It just occured to me as I was switching off the PC that I would have had the exhaust can removed before I touched that front bracket, and that's a whole other ball game unless you are set up for doing more work (read how to section end to end). This may be why others are keeping quiet now. :?

Did you get the strap in ok just by removing the bolt? With the can still in place you may be able to hold nut in place by a blob of blue tack on the end of a screw driver while you insert bolt. Patience and practice! ;)


Top
PostPosted: 05 Aug 2012 10:08 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Yes, bolt taken completely out, bracket eased down from block to give enough space to get the strap in. Just need to get the nut on the bolt as bolt goes in hole easily enough, just keeps pushing the nut out of the recess as I turn the hex bolt....as you say, patience 8-)


Top
PostPosted: 05 Aug 2012 12:26 
Offline

Joined: 08 Apr 2011 19:13
Posts: 321
Current ride: Tl1000s
Location: worthing west sussex
Bolt & nut back in, just took a bit more time.....
Off to Brands for a trackday tomorrow so I'll keep the chin fairing off so I can keep an eye on it all for now. Looks like a short day as rain forecast pm which is no god for the power one / rennesport pairing I've just put on :oooops:
Thanks for the help everyone.


Top
PostPosted: 06 Aug 2012 09:29 
Offline
User avatar

Joined: 08 May 2009 13:13
Posts: 3651
Current ride: XB9SX
birdy wrote:
Bolt & nut back in, just took a bit more time.....
Off to Brands for a trackday tomorrow so I'll keep the chin fairing off so I can keep an eye on it all for now. Looks like a short day as rain forecast pm which is no god for the power one / rennesport pairing I've just put on :oooops:
Thanks for the help everyone.


Well done! As you probably gathered, removing the rear straps can involve having to slacken the belt to remove the belt tensioner, unless like some of us you've had the rear straps reversed for quick access and pipe swaps! ;)


Top
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 28 posts ]  Go to page Previous 1 2

All times are UTC


Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited