It is currently 16 Nov 2024 17:25

Unanswered topics | Active topics


Home » Board index » The Bike Bit » Technical Forum

All times are UTC



Post new topic  Reply to topic  Page 1 of 3
  [ 44 posts ]  Go to page 1 2 3 Next
  Print view Previous topic | Next topic 
Author Message
WILLYBUELL
PostPosted: 04 Sep 2012 22:35 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
OK ,so trundaling along at 80 ont way home from the manx yesterday when me oil light comes on about 15 miles from nottingham :shock: ,clocked it stright away n killed the motor :D HMMMMMM HMMMMMMM ,start grumbly quite noisy lifters kill engine again ,home ont yellow taxi :rotfl: :rotfl: ,need to buy one o these fuckers at this rate ,pics say it all ,oil pump drive gear fooked,oil pump ok ,cam bushes ok ,mains ont offside fooked ,play in roller bearing felt when lifting shaft up n down ,dont need to put a clock on it ,THERE FOOKED ,milage 29000 ,not botherd about the crank got a spare ,REASONS YOU SHOULD change your oil pump gear ,1 recon my mains have worn because of all the oil bound ultra fine bebris in the oil can get into the mains via the gap in the circlip you can see in the pic at 11 oclock,big ends my survive due to the oil being filterd before the oil gets there ,2 if you DONT spot you oil light on like i did BLOODY expensive rebuild ,so if your gonna keep you XB ,GET a gear of pash and stand the cost of fitting and hopefully one thing less to worry about :yup:


Attachments:
Picture 007.jpg
Picture 007.jpg [ 253.58 KiB | Viewed 1439 times ]

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER
Top
  Send private message  
Reply with quote  
Maz
PostPosted: 04 Sep 2012 22:50 
Offline
Site Admin
User avatar

Joined: 15 Apr 2009 17:17
Posts: 8642
Location: Manchester
So, yet another one bites the dust......should've spent more time on basic maintainance than grinding brake discs etc. :)

If you're gonna renew that pinion needle race/RH main.....please post pix as I cant wait to see how you go about it.....new inner race has to be ground on the crank, new outer race has to be lapped in situ......both to within 0.0002'' for roundness and taper and a mega surface finish (16RMS from memory)......good luck :yup:

_________________
Mithered ta death.
92 MB
96 S2T
98 S1W
00 M2
01 X1
03 P3
10 CR
Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 04 Sep 2012 23:29 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
mate the only thing i didnt do and should have is pulled the oil pump n looked up its ares to see if drive gear was failing ,GUILTY as charged there :D ,as for basic maintainance ,tut tut maz ,grumbly gets tugged n pulled in all the right areas before a long run ,OOA except when i left the front calipher skt/caps loose first time to ems do ,again guilty as charged there ,WHOOOOOOO maz grumbly hasent bit the dust :shock: good lord nooooooooooooo. me n von have been looking playing in the engine for sum time now ,seems the ideal time dont you think ;) we got ideas :yup: buy the way whots 16 rms mean cause ive got no fucking idea :twisted: will have to talk with von on that one :yup: maz recon you need to spend time with von :D ,genarally speaking von dont work to thousands of an inch ,microns is the derigure in his workshop ,in fact all von DTI,s are in a finer calibration :yup: ,thanks for the good luck maz ,but recon we will have it well coverd , :D :D

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
Maz
PostPosted: 05 Sep 2012 00:01 
Offline
Site Admin
User avatar

Joined: 15 Apr 2009 17:17
Posts: 8642
Location: Manchester
0.0002 is microns :roll: .......and DTI's dont get calibrated as such :)

_________________
Mithered ta death.
92 MB
96 S2T
98 S1W
00 M2
01 X1
03 P3
10 CR
Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 05 Sep 2012 00:06 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
Maz wrote:
.0002 is microns :roll: .......and DTI's dont get calibrated as such :)

just teasing mate ,if we need help youll get a call :D :yup:

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
Maz
PostPosted: 05 Sep 2012 00:14 
Offline
Site Admin
User avatar

Joined: 15 Apr 2009 17:17
Posts: 8642
Location: Manchester
No worries......I have all the measuring equipement and tools required to meet the tolerances but you will need to split the crank to have the new inner race precision ground to size :idea:

_________________
Mithered ta death.
92 MB
96 S2T
98 S1W
00 M2
01 X1
03 P3
10 CR
Top
  Send private message  
Reply with quote  
pash
PostPosted: 05 Sep 2012 12:16 
Offline
proff. patpending
User avatar

Joined: 06 May 2009 20:20
Posts: 14705
Current ride: Victoria Sponge
Location: Bristol - Gateway to all things good
Last orders for Lucky Hands oil pump drive gears, payment by Friday...

viewtopic.php?p=206373#p206373

Order should be with me at the end of next week ready for posting out.

I doubt I will be doing another order after this one, the original intent was to get a discount on a gear for myself (which I allowed someone else to have - i.e. I am still waiting for mine), but the interest grew. If think I am keeping stock, you are mistaken, so if you are thinking of one for the future, buy now to avoid disappointment...

Note the state of Willy's engine, I would say he was lucky. If you want an insurance policy against this I suggest you get a gear. If you are daunted by having to fit it yourself, find simeone to do it for you (and that someone is not me), PM Maz or Tubbs or find a competent independant to help.

_________________
08 Specialized Langster
Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 05 Sep 2012 13:02 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
:yt:

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
Adam
PostPosted: 05 Sep 2012 13:11 
Offline
Moderator
User avatar

Joined: 15 Apr 2009 17:25
Posts: 11772
Location: Oswestry
...........and as extra insurance, I would like to add, DO NOT cane your motor until it is properly warm ie at least 5 miles ;)

_________________
If your dreams don't scare you, they are not big enough.
Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 05 Sep 2012 13:36 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
root mean squared ,right bearing bill so far 78 squid just for the cases ,i allready know brian whont be happy to pay that ,already looking at alternatives he is :D

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
Maz
PostPosted: 05 Sep 2012 17:42 
Offline
Site Admin
User avatar

Joined: 15 Apr 2009 17:17
Posts: 8642
Location: Manchester
78 quid for what ??......unless prices have gone up considerably (probably :x ) since I last stocked up......

Pinion brg. outer race - 10.20
Pinion brg. inner race - 14.43
Pinion brg. needle race - 9.34

Total = £33.97 incl. vat

_________________
Mithered ta death.
92 MB
96 S2T
98 S1W
00 M2
01 X1
03 P3
10 CR
Top
  Send private message  
Reply with quote  
cooter
PostPosted: 05 Sep 2012 19:12 
Offline
User avatar

Joined: 08 Apr 2010 20:05
Posts: 623
Location: West Country
WILLYBUELL wrote:
[color=#0000FF]OK ,so trundaling along at 80 ont way home.......


There's your problem

_________________
Buell X1 PBS
Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 05 Sep 2012 22:48 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
Maz wrote:
78 quid for what ??......unless prices have gone up considerably (probably :x ) since I last stocked up......

Pinion brg. outer race - 10.20
Pinion brg. inner race - 14.43
Pinion brg. needle race - 9.34

Total = £33.97 incl. vat

bob on with those prices ,but being it is my opinion that the off side bearing has failed early due to oil bound debris from the degrading oil drive pinion shortening its service life ,i feel the nearside crankcase bearing needs replacing as well ,as a refurb on the big end needs doing at the same time too , just to be sure while the engine in bits ,i find it odd you have not advised to do this while the engine down ,but recomend wheel bearing be changed with every tire change regardless ,ooa nearside bearing 36,52

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
WILLYBUELL
PostPosted: 05 Sep 2012 22:54 
Offline
Think Pink
User avatar

Joined: 07 Jun 2010 00:37
Posts: 3777
Current ride: Awesome Ulysses & X1
Location: balderton, newark
greasemonkey wrote:
,,who the fuck is "Brian Whont" Willy ?

shite spelling ian just how it youth :rotfl: :rotfl: :yup:

_________________
IF IT BLEEDS WE CAN KILL IT ,THIS STUFF WILL MAKE YOU A GODDAM SEXUAL TYRANASURUS ,YOUVE BEEN PUSHING TOO MANY PENCILS DILLON .GET TO THE CHOPPER


Top
  Send private message  
Reply with quote  
pash
PostPosted: 05 Sep 2012 22:55 
Offline
proff. patpending
User avatar

Joined: 06 May 2009 20:20
Posts: 14705
Current ride: Victoria Sponge
Location: Bristol - Gateway to all things good
You could do a Timken conversion on the primary side and control your end float.

_________________
08 Specialized Langster
Top
  Send private message  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic  Reply to topic  Page 1 of 3
  [ 44 posts ]  Go to page 1 2 3 Next

Home » Board index » The Bike Bit » Technical Forum

All times are UTC

Who is online

Users browsing this forum: No registered users and 33 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited