It is currently 14 Dec 2024 16:44

All times are UTC




Post new topic  Reply to topic  [ 44 posts ]  Go to page Previous 1 2 3
Author Message
PostPosted: 01 Apr 2014 17:09 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7259
Current ride: 1991 RS1200 westwind
tyranomonkey wrote:
ah... found a discussion on this on the "other" buell forum.

i think if no-one looks closely i can maybe knock up something similar to the :maz: one. unless anyone has one going spare they would like to sell me?

Attachment:
01-04-2014 12-39-23.jpg


I think you will find that photo is Muffin wearing his Maz bracket ;) ............. far superior to the genuine shoe type fitting that clamped to the top of the pipe .

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.


Top
PostPosted: 07 Apr 2014 07:16 
Offline
User avatar

Joined: 13 Sep 2013 10:26
Posts: 72
Current ride: M2 cyclone 2002
Location: aberdeen
Started polishing yesterday. Flattened both batteries on my cordless drill, then went to plug in the charger. Turned it on at the wall and about 4 seconds later the f**king charger exploded. Not the battery itself, the adapter part that plugs into the wall socket. Scared the sh*t out of me, and my ears were ringing for sbout an hour.

Gonna buy an old school corded drill today. The half polished look is worse than the not polished look.

_________________
M2 '01 - serviced and tweaked by Maz, rescued from the mill of doom by the kind people of UKBEG


Top
PostPosted: 07 Apr 2014 10:18 
Offline
Mr. Tourettes
User avatar

Joined: 06 May 2009 13:51
Posts: 2450
Location: cambs
I went to B&Q a couple of weeks ago and paid £25 for one, there was a 15 quid one. I am doing the same as you at the moment. I wanted variable speed, compact and light, the 710w 'performance power' PHD710A fitted the bill and is doing a great job. :idea:

_________________
xxxx


Top
PostPosted: 07 Apr 2014 11:55 
Offline
User avatar

Joined: 13 Sep 2013 10:26
Posts: 72
Current ride: M2 cyclone 2002
Location: aberdeen
noted Richie, cheers.

Just spoke to warrenty folk about my drill. they're going to send me a new charger for free, once i post them the exploded one. and they offered to pay the postage for the old one. and they're doing all this without me having my reciept to hand.

reading between the lines, they're either terrified about having to do a product recall, or worried that i'll blab on the interweb about them being "a bit explodey".

JCB 20V lithium combi drill for your info folks. great when it works, just make sure to turn the charger on with a broom handle whilst standing behind an inch of lexan.

_________________
M2 '01 - serviced and tweaked by Maz, rescued from the mill of doom by the kind people of UKBEG


Top
PostPosted: 07 Apr 2014 12:06 
Offline
User avatar

Joined: 06 May 2009 16:03
Posts: 4389
Current ride: S1w X1 1125CR
Location: NNW of Sarfampton
tyranomonkey wrote:
JCB 20V lithium combi drill .


Hmm where's Digger when you need him?

_________________
I'm a Hornithologist, I get excited by exotic birds.........


Top
PostPosted: 07 Apr 2014 18:22 
Offline
Moderator
User avatar

Joined: 15 Apr 2009 17:25
Posts: 11772
Location: Oswestry
tyranomonkey wrote:
noted Richie, cheers.

Just spoke to warrenty folk about my drill. they're going to send me a new charger for free, once i post them the exploded one. and they offered to pay the postage for the old one. and they're doing all this without me having my reciept to hand.

reading between the lines, they're either terrified about having to do a product recall, or worried that i'll blab on the interweb about them being "a bit explodey".

JCB 20V lithium combi drill for your info folks. great when it works, just make sure to turn the charger on with a broom handle whilst standing behind an inch of lexan.



Idealy, if you're taking bits off the bike, you really want a big bench grinder because it helps get some heat into the work and drills are a bit weedy when it comes to this. My mate has a 2hp wheel with big mops on it. You only let it grab once :shock: lOl lOl

_________________
If your dreams don't scare you, they are not big enough.


Top
PostPosted: 09 Apr 2014 23:24 
Offline
User avatar

Joined: 07 May 2009 12:06
Posts: 487
Current ride: 2001 M2
Reminds me of my schooldays when we had a rather weak metalwork teacher.....we would stand around the classroom playing cricket.....the idea was that the 'batsman' dropped a small polishing wheel onto the fast spinny big wheel....6 runs if you hit the wall etc.... :D


Top
PostPosted: 13 Apr 2014 16:39 
Offline
User avatar

Joined: 13 Sep 2013 10:26
Posts: 72
Current ride: M2 cyclone 2002
Location: aberdeen
Drilled out the rivets very easily, but the end caps of silencer have been stuck in place with a red mastic type stuff. Any suggestions? And do I need to replace said annoying mastic when I put it back together?

Thinkin I might try of that goop you get to eat away bathroom sealant.

_________________
M2 '01 - serviced and tweaked by Maz, rescued from the mill of doom by the kind people of UKBEG


Top
PostPosted: 13 Apr 2014 18:43 
Offline
proff. patpending
User avatar

Joined: 06 May 2009 20:20
Posts: 14705
Current ride: Victoria Sponge
Location: Bristol - Gateway to all things good
Use some silicon sealant remover.

Don't use mastic again.

_________________
08 Specialized Langster


Top
PostPosted: 17 Jul 2014 22:18 
Offline
User avatar

Joined: 13 Sep 2013 10:26
Posts: 72
Current ride: M2 cyclone 2002
Location: aberdeen
So, quarter of a year later, I finally had time and inclination to put the exhaust on. Freshly polished, new acoustafil packing, and a lovely new "maz bracket". Also, MOT passed last week with the old stock exhaust.

Started it up in a relatively enclosed area and scared myself a bit. :) once it warmed up a bit it settled down to a really nice level of noise, not too offensive (which I feared). But i'm glad I'll already be awake when its started in the morning. Neighbours might not appreciate their new alarm clock.

Thanks maz, pash, kev, daveh and everyone else for advice and bits etc. Much appreciated.


Attachments:
20140717_211524.jpg
20140717_211524.jpg [ 1.94 MiB | Viewed 637 times ]

_________________
M2 '01 - serviced and tweaked by Maz, rescued from the mill of doom by the kind people of UKBEG
Top
PostPosted: 23 Jul 2014 11:11 
Offline
User avatar

Joined: 13 Sep 2013 10:26
Posts: 72
Current ride: M2 cyclone 2002
Location: aberdeen
so, i've got the stock carb on it, but with the stage one trimmings. mikuni and forcewinder will be this winter's task, but for the moment, would it be worth the effort to get the carb jetted specifically to suit the race exhaust? seems to be performing pretty well at the moment, but am i missing some of the potential by keeping the original settings?

made someone swear loudy when i started it at work the other day. it seems there's a little knack to getting the exhaust to pop with a quick flick of the throttle when at idle. :twisted:

_________________
M2 '01 - serviced and tweaked by Maz, rescued from the mill of doom by the kind people of UKBEG


Top
PostPosted: 27 Mar 2015 07:59 
Offline
User avatar

Joined: 06 May 2009 13:55
Posts: 4509
Current ride: GTR1000 Rocket,550GT
Location: Joondalup
rik wrote:
pash wrote:
And use stainless rivets otherwise they are likely to break...

:yt: ...or simply wear away with the vibration! They really need to be the sealed type too.


Would anyone know the correct size of the rivets ? I'm new to riveting and they seem to come in all sorts of different sizes. Also, are sealed stainless rivets harder to get hold of? Just been to Bunnings, the Oz B&Q, and they seemed to have everything except sealed stainless.

_________________
Wear the fox hat


Top
PostPosted: 27 Mar 2015 09:20 
Offline
User avatar

Joined: 06 May 2009 19:42
Posts: 3153
Current ride: M2 Razorback
Location: Mouth of the Port in the Shire of Hamp
Bonz, STOP! Before you drill out those very hard to find rivets....
It reads (above) as though it was only repacked very recently and can't have run very much since, so I doubt a lack of wadding is the issue... it may already be as quiet as it's ever going to be! Get a Db killer type of baffle inserted.

_________________
'98 M2 Razorback, it's a keeper.


Top
PostPosted: 27 Mar 2015 09:36 
Offline
User avatar

Joined: 06 May 2009 13:55
Posts: 4509
Current ride: GTR1000 Rocket,550GT
Location: Joondalup
rik wrote:
Bonz, STOP! Before you drill out those very hard to find rivets....
It reads (above) as though it was only repacked very recently and can't have run very much since, so I doubt a lack of wadding is the issue... it may already be as quiet as it's ever going to be! Get a Db killer type of baffle inserted.


Don't worry, I'm not drilling out anything until I've got all the kit I need and as much instruction as I need. I've hijacked this thread, it's not mine being talked about, but it's the same one. I don't know if mine has ever been repacked, but anyway, 1st thing is a Db killer, it's on its way :P

_________________
Wear the fox hat


Top
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 44 posts ]  Go to page Previous 1 2 3

All times are UTC


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited