It is currently 24 Nov 2024 00:28

Unanswered topics | Active topics


Home » Board index » The Bike Bit » Technical Forum

All times are UTC



Post new topic  Reply to topic  Page 1 of 1
  [ 12 posts ] 
  Print view Previous topic | Next topic 
Author Message
thunderer
PostPosted: 06 Jun 2018 20:58 
Offline
User avatar

Joined: 23 May 2010 10:44
Posts: 154
Current ride: X1W m2
Location: oxfordshire
4 bent valves 4 bent push rods. Stripped gear case and found broke key between oil pump drive gear and pinion any ideas what coursed this and do I need to look further in engine.

_________________
X1 Whitelightning 2002
S3T 2000
Montessa Cota 349 1982
Kawasaki Hardtail 1983
Beta rev3 250
Top
  Send private message  
Reply with quote  
Nutah
PostPosted: 06 Jun 2018 21:10 
Offline
User avatar

Joined: 05 May 2009 20:00
Posts: 10973
Current ride: X1 2001
Location: southampton
:shock:
with all that damage , i would strip it right down & check the whole motor

_________________
Feros Ferio
Top
  Send private message  
Reply with quote  
DaveH
PostPosted: 06 Jun 2018 21:31 
Offline

Joined: 07 May 2009 21:27
Posts: 1354
Current ride: XB12s,S1WL, Triumph
Location: Glossop in't th'hills
:yt:
Top
  Send private message  
Reply with quote  
thunderer
PostPosted: 06 Jun 2018 23:22 
Offline
User avatar

Joined: 23 May 2010 10:44
Posts: 154
Current ride: X1W m2
Location: oxfordshire
That's my line of thought also safe than sorry in the long run

_________________
X1 Whitelightning 2002
S3T 2000
Montessa Cota 349 1982
Kawasaki Hardtail 1983
Beta rev3 250
Top
  Send private message  
Reply with quote  
Nutah
PostPosted: 07 Jun 2018 09:05 
Offline
User avatar

Joined: 05 May 2009 20:00
Posts: 10973
Current ride: X1 2001
Location: southampton
definitely.
good luck

_________________
Feros Ferio
Top
  Send private message  
Reply with quote  
DaveH
PostPosted: 08 Jun 2018 20:29 
Offline

Joined: 07 May 2009 21:27
Posts: 1354
Current ride: XB12s,S1WL, Triumph
Location: Glossop in't th'hills
Out of interest is it the original oil pump drive gear or a lucky hands type. Has it stripped the teeth off the cam gears or pinion gear. Is the oil pump still free to turn. ?
Top
  Send private message  
Reply with quote  
thunderer
PostPosted: 09 Jun 2018 10:42 
Offline
User avatar

Joined: 23 May 2010 10:44
Posts: 154
Current ride: X1W m2
Location: oxfordshire
Changed original drive gear at 42,000 very worn fitted replacement harley then as hadn't got LH gear. Have now so will rebuild with it. No teeth stripped and oil pump turns freely.

_________________
X1 Whitelightning 2002
S3T 2000
Montessa Cota 349 1982
Kawasaki Hardtail 1983
Beta rev3 250
Top
  Send private message  
Reply with quote  
jeznewsome
PostPosted: 09 Jun 2018 10:50 
Offline
User avatar

Joined: 23 Jun 2009 12:55
Posts: 658
Current ride: S1W,Hype,HP2,R1200RS
Location: Preston, Lancs
so what caused the key to break?
Top
  Send private message  
Reply with quote  
kevmean
PostPosted: 09 Jun 2018 10:59 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7259
Current ride: 1991 RS1200 westwind
Dropped a valve first? or rear big end gone causing piston to hit valve and the shock loading sheared the key ? Was the pinion nut still tight?

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.
Top
  Send private message  
Reply with quote  
kevmean
PostPosted: 09 Jun 2018 11:01 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7259
Current ride: 1991 RS1200 westwind
Also which bike and had it had any engine work done recently?

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.
Top
  Send private message  
Reply with quote  
thunderer
PostPosted: 09 Jun 2018 11:34 
Offline
User avatar

Joined: 23 May 2010 10:44
Posts: 154
Current ride: X1W m2
Location: oxfordshire
Pinion nut still tight never touched top end oil pump drive gear changed over thousand miles ago. It is a x1 2001 engine I will show you a pic when I see you next Kev.

_________________
X1 Whitelightning 2002
S3T 2000
Montessa Cota 349 1982
Kawasaki Hardtail 1983
Beta rev3 250
Top
  Send private message  
Reply with quote  
kevmean
PostPosted: 10 Jun 2018 10:35 
Offline
User avatar

Joined: 06 May 2009 17:28
Posts: 7259
Current ride: 1991 RS1200 westwind
thunderer wrote:
Pinion nut still tight never touched top end oil pump drive gear changed over thousand miles ago. It is a x1 2001 engine I will show you a pic when I see you next Kev.

When you say never touched top end did you remove the rockers when you changed the oil pump gear? If you did but didn't give lifters enough time to bleed down on rebuilding it may have caught a valve when you turned it over bending it very slightly and causing it to foul fully later.
If you didn't you could still have caused damage when refitting the cam cover.

_________________
2001 X1 2009 1125CR 2006 Uly X3 2010 Uly a fully Maz'd S1 and a 1991 RS1200 Westwind.
Top
  Send private message  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic  Reply to topic  Page 1 of 1
  [ 12 posts ] 

Home » Board index » The Bike Bit » Technical Forum

All times are UTC

Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited